Property Repair Systems

01626 331351

STRUCTURAL EPOXY RESIN - THIXOTROPIC EPOXY RESIN - THIXO RAPID RESIN -

PURE EPOXY RESIN -

MOULDABLE EPOXY PUTTY - PRIMER/CONSOLIDATOR - TIMBABUILD -

JOIST END REPAIR KITS - JOIST SPLICE KITS - TIMBER RESIN SPLICE KITS -

EXTENDED 3D CUTTER - EXTENDED STEEL CHISEL - CARTRIDGE TUBES -

EXTENSION NOZZLES - SKELETON GUNS

Structural Epoxy Resins - pour directly or into a 1 litre cartridge tube for injection - e.g. concrete or timber holes or cracks

A three part, (two liquids and a powder) thick pouring resin. The thickness can be modified by varying the amount of powder used. Mix using a mixing paddle in an electric drill. For filling holes and, in combination with reinforcement rods, for structural repair of timber and masonry, including concrete. Self levelling, self de-gassing.

Usage rate - by volume - 1 litre will fill a void 100mm x 100mm x 100mm (4" x 4" x 4").

Frequently purchased with this product - Mixing Paddle, 1 litre Cartridge Tube Kit, 1 litre Skeleton Gun.

£27.80 1 litre, £53.35 2.5 litre, £121.00 7.5 litre, plus VAT

Structural Pouring Resin - 1 litre 2.5 litres

7.5 litres

Mixing Paddle -

Empty 1 litre Cartridge Tubes -

Skeleton Gun 1 litre -

1 Litre Injection Accessory Kit - box of 100 gloves, 1000cc skeleton gun, mixing knife

A two part, (two pastes) thick injection resin. Mix using a pallet knife, by hand. For laminating and bonding materials together. In conjunction with a Cartridge Tube kit, for injecting into slots and holes and, in combination with reinforcement rods, for structural repair of timber and masonry, including concrete. Also used as an anchor resin, to bond rods, studs, bolts and reinforcement into masonry and concrete.

Usage rate - by volume - 1 litre will fill a void 100mm x 100mm x 100mm (4" x 4" x 4"). A 400cc pack will fill a hole 25mm in diameter to a depth of 800mm. Extension tubes are available, made to order, to reach the base of any hole depth and in varying diameters.

Frequently purchased with this product - Pallet Knife, 400cc Cartridge Tube Kit, 400cc Skeleton Gun, 1 litre Cartridge Tube Kit, 1 litre Skeleton Gun, Vinyl Gloves (Box of 100).

£22.55 400cc, £29.77 1 litre, both require a Cartridge (at extra cost) if being used for injection, rather than spreading

Thixotropic 400cc Resin 1 Litre resin

pallet knife box of gloves

400cc Injection Accessory Kit - box of gloves, 400cc skeleton gun, mixing knife

1 Litre Injection Accessory Kit - box of gloves, 1000cc skeleton gun, mixing knife

Cartridges - with pistons, nozzles and loading plates - 400cc 1000cc

Extension Nozzles - 16mm diameter - 400mm long - 400cc 1000cc

Extension Nozzles - 10mm diameter - 400mm long - 400cc 1000cc

For rapid setting injection with the resins mixed in the nozzle - 6 to 8 minutes, in a single plastic cartridge. Simply insert into a standard skeleton gun and screw on the spiral mixing tube. Inject gently, like putting paste on your toothbrush, from the bottom of the hole outwards. Can be used for anchors, bolts, studs and stitching in masonry. Buy spare mixing tube nozzles to avoid wasting part tubes, if you need to stop and start.

Usage rate - 280cc will fill a 10mm x 100mm slot for a length of 280mm (a typical 'stitch' repair would be 225mm long).

Frequently purchased with this product - 400cc Professional Skeleton Gun, Spare Mixing Nozzles, Vinyl Gloves.

£14.50 single tube with one mixing nozzle, £0.58 per spare mixing nozzle, plus VAT

Thixo Rapid 280cc - . Spare mixing nozzles -

Box of gloves (100) -

Stitching Epoxy-Glass Rod - 6mm diameter x 1 metre -

280/400cc Injection Accessory Kit -

Includes a box of 100 gloves, 400cc skeleton gun, nozzle, mixing knife -

For repairs to metal, masonry and wood - Pure Epoxy Resin, supplied in a dual piston, side by side plastic cartridge. Simply insert into a 1:1 ratio skeleton gun and screw on the mixing tube. Inject from the bottom of the hole outwards or spread onto mating surfaces. Can be used for anchors, bolts, studs and stitching in masonry, bonding and laminating - suitable for use with steel, stainless steel, aluminium, brick, stone and render.

Usage rate - 380cc will fill 8 x 20mm diameter holes to a depth of 150mm, assuming maximum wastage. For surface bonding or lamination allow a minimum of 1 litre per square metre, assuming a thickness of 1mm.

Frequently purchased with these products - 1:1 Skeleton Gun, Vinyl Gloves, Spare Mixing Nozzles

Pure Epoxy Resin - £17.86 per 380cc cartridge including mixing nozzle, plus VAT

Pure Epoxy 380cc Resin -

Box of 100 gloves - Spare mixing nozzles -

Special Injection Gun - side by side 1:1 -

Simply take equal portions in gloved hands and mix together, like window putty or bread dough, until a perfectly even colour. Apply with a pallet knife or by hand placing. Can be sanded and painted, or left a natural buff colour. Can also be coloured with Mortar Powder or you can add you own stone dust to the finished surface whilst uncured.

Usage rate - 1 litre of putty will fill a hole 4 inches x 4 inches x 4 inches (100mm x 100mm x 100mm).

Frequently purchased with this product - Vinyl Disposable Gloves (Box of 100 uni-handed vinyl), Epoxy Primer 500cc.

Mouldable Epoxy Putty, 1 litre, £15.75, plus VAT -

Pallet knife £9.52, plus VAT -

Box of 100 gloves, £10.97, plus VAT -

Epoxy Primer, 500cc, £16.50, plus VAT -

Discounted Offer

Complete Putty Repair Kit, £36.24, plus VAT-

(Contains 1 x 1 litre of putty, box of gloves, putty knife).

Epoxy Primer is always specified for masonry, smooth timber, planed timber and all hardwoods.

However, on rough or well dug out softwood timber it is not strictly required.

Ensure that ALL rotted wood is cut out completely. Filling over rot is a waste of money.

Finish the job off with our Boron Paste and Boron Rods - these provide internal protection by dissolving inside. See our Boron Shop for details.

A thin, two part epoxy liquid. Primes and consolidates timber, concrete, brick stone and render.

Provides a secure bond on wood, metal, concrete, render, stone, brick and quarry tiles. Apply by brush or roller. Pure epoxy - no solvents, no water. Apply the repair resin (e.g. Mouldable Putty) into the repair while the Epoxy Primer is still tacky.

Usage rate - allow between 1 square metre per litre (rough surfaces) and 2.5 square metres per litre (smooth surfaces)

Colours - Clear - other colours to Order

Epoxy Primer/Consolidator - £16.50 500cc, £25.05 1 litre, plus VAT

Buy Primer/Consolidator - 500cc -

Buy Primer/Consolidator - 1 litre -

Buy pallet knife for mixing - - Buy box of 100 disposable gloves -

Repair window frames, door frames, timber frames with TIMBABUILD or TIMBABUILD RAPID. Designed for window frame care and repair, this filler/adhesive consists of two soft, creamy materials, gunned to give a perfect mix ratio. Mix with a putty knife. There is no shrinkage and it is totally waterproof. This is a professional repair material, as used by window frame repair specialists.

Usage rate - 380cc will fill a 10mm x 100mm slot for a length of 380mm

Frequently purchased with this product - 380cc Skeleton Gun, Spare Mixing Nozzles, Vinyl Gloves, Epoxy Primer.

Timbabuild Rapid Set - £25.60 per tube, plus VAT -

Timbabuild Standard Set - £24.50 per tube, plus VAT -

Timbabuild Skeleton Gun,

for Rapid or Standard Set - £28.90, plus VAT -

Epoxy Primer, 500cc - £16.50, plus VAT -

Box of 100 gloves - £10.97, plus VAT -

Epoxy Primer is always specified for smooth timber, planed timber and all hardwoods.

However, on rough or well dug out softwood timber it is not strictly required.

Ensure that ALL rotted wood is cut out completely. Filling over rot is a waste of money.

Finish the job off with our Boron Paste and Boron Rods - these provide internal protection by dissolving inside. See our Boron Shop for details.

Joist Repair - end plates and splice plates

Joist End Repair Plates are supplied as pairs of galvanised steel plates, pre-drilled, to be fixed with Coach Screws (included). The plates rest in or on the wall and allow for the rotted end to be cut off.

BM6 Plates - allow for up to 6 inches, 150mm, to be cut off - joist size 4 inches, 100mm deep, or more

BM9 Plates - allow for up to 9 inches, 225mm, to be cut off - joist size 4 inches, 100mm deep, or more

Only for joists 6 inches, 150mm, deep or larger,

BM17 Plates - allow for up to 17 inches, 432mm, to be cut off

BM6 Kit - - £17.78 plus VAT

BM9 Kit - - £22.28 plus VAT

BM17 Kit - - £26.77 plus VAT

Joist Splice Plate Kits are supplied as pairs of plates made from anodised aluminium treadplate, un-drilled, to be fixed with self drilling and tapping screws (included). The plates allow you to joint domestic joists at any point along their length.

JSP Small Kit - for joists from 4 inches up to 6 inches, 100mm - 150mm, in depth

JSP Medium Kit - for joists from 6 inches to 8 inches, 150mm - 200mm, in depth

JSP Large Kit - for joists from 8 inches up to 10 inches, 200mm to 250mm, in depth

JSP Small Kit - - £17.50 plus VAT

JSP Medium Kit - - £22.50 plus VAT

JSP Large Kit - - £27.60 plus VAT

Timber-Resin Splice Kit - beam end repair - bearing ends or mid-span sections

For repairing timber beams, lintols, rafters, tie beams, carrier beams, joists and bressumers. These bespoke beam kits contain a new, laminated structural timber, made in kiln dried wood to C24 Grade or higher, fitted with connector bars made from zinc plated 8.8 Grade High Tensile Allthread bar. Pouring or injection resins are also included.

Engineering - free Design, Method Statement and Tools List (Hire available).

Frequently purchased with this product - additional Structural Pouring Resin

£ POA - price on application, Immediate Free Quotation - call Angela or Andy on 01626 331351

We also manufacture unusual shaped timber repair components: for example, on the left

we have a Pizza Hut building with new frame legs, on the right a timber Tower part.

Strength Upgrades - reduce deflection - sagging beams, change of use: domestic to commercial

For stiffening timber beams, lintols, rafters, tie beams, carrier beams, joists and bressumers. Steel reinforcement, made from zinc plated 8.8 Grade High Tensile Allthread bar, or BS4449 Rebar is laid into a central slot and then Structural Epoxy Pouring resin is added to form a permanent upgrade. This 'modified flitch' usually doubles the stiffness of the average beam.

Engineering - free Design, Method Statement and Tools List (Hire available).

Frequently purchased with this product - additional Structural Pouring Resin

£ POA - price on application, Free Quotation - call Angela or Andy on 01626 331351

3D Cutters - deep hole and slot cutting

A high speed tool for use in electric drilling machines. The 3D Cutter drills holes, cuts slots and can be dragged sideways to clean out previously rough drilled or cut out slots or holes.

25mm diameter x 110mm length - - £24.40 plus VAT

32mm diameter x 110mm length - - £25.83 plus VAT

Extended length versions:

25mm diameter x 250mm length - - £38.50 plus VAT

32mm diameter x 250mm length - - £39.77 plus VAT

All Metal Chisels - deep slot clearance

All Metal Chisels, made of solid steel, can be used with lump hammers and as levers, to clean out slots and tidy up previously roughly cut out cavities in wood.

Standard length;

30mm wide - - £19.87 plus VAT

Extended length

30mm wide - - £39.87 plus VAT

Cartridge Tubes - for hand filling

400cc Cartridges and extension tubes

400cc Cartridge Tubes, with piston and standard nozzle - £1.50 plus VAT

400cc Extended Nozzles - 8mm - £2.85 10mm - £3.20 16mm - £3.85 all pus VAT

400cc Cartridge -

Extended Nozzle Tube - 8mm diameter x 400mm long -

Extended Nozzle Tube - 10mm diameter x 400mm long -

Extended Nozzle Tube - 16mm diameter x 400mm long -

1 Litre cc Cartridges and extension tubes

1 Litre Cartridge Tubes, with piston and standard nozzle - £3.55 plus VAT

1 Litre Extended Nozzles - 10mm - £3.60 16mm - £4.10 all plus VAT

1 Litre Cartridge -

Extended Nozzle Tube - 10mm diameter x 400mm long -

Extended Nozzle Tube - 16mm diameter x 400mm long -

Extension Nozzles - for cartridge tubes - 400cc or 1 Litre fitting

Extension Nozzles - 8mm diameter - 400mm long - for 400cc Tube -

Extension Nozzles - 10mm diameter - 400mm long - for 400cc Tube -

for 1 Litre Tube -

Extension Nozzles - 16mm diameter - 400mm long - for 400cc Tube -

for 1 Litre Tube -

Skeleton Guns - for single and double tubes

400cc Skeleton Gun - for injection using UltraCure 400cc and all other products in single tubes, 280cc to 400cc

1 Litre Skeleton Gun - Special 1000cc gun for injection using UltraCure 1000cc or other 1 Litre products.

380cc 1:1 Skeleton Gun - gun for injecting Anchor Resin and similar 1:1 side by side resin cartridges

£14.50 400cc gun, £24.70 1000cc (1 litre) gun, £28.90 380cc/1:1 mix ratio, plus VAT

400cc gun -

1000cc gun -

380cc/1:1 gun -

pallet knife -

box of 100 gloves -

Looking for a solution to a problem:

• Joist end repair - use Joist End Repair Kits
• Joist span repairs - use Joist Splice Plates
• Beam Cracks and Splits - use Mouldable Epoxy Putty
• Injection of Slots or Cracks - use Thixotropic Injection Resin or Pure Epoxy
• Injection of Stitching Slots or Anchor Holes - use Thixo Rapid
• Filling holes or cavities by pouring - use Structural Epoxy pouring Resin
• Timber Beam end failure - use a Timber-Resin Splice kit

Free Technical Advice on all these subjects: call Angela, Andy or David on 01626 331351

Home | Repairs | Beams | Roof | Mold | Dry Rot | Privacy Policy | Returns Policy | Contact